CAR PARK FANS

Car Park fans are for ventilation and fire control in roofed facilities like underground carparks, carpark tower blocks etc. The system is unique as it is without ducts and uses the impulse principle to move air. Often the designs include axial flow fans for supply or exhaust air. The advantages are lower construction cost and better space utilisation.

The Novenco Car Park Fans series are available as unidirectional or reversible units and include versions with silencers or with silencing technology.

Designs are oval, round or flat with thrusts between 5 and 111 N, rated power from 0.1 to 2.2 kW and sound pressures from 35 to 75 db(A).


Jet Fans AUZ ARP

Oval design car park jet fans in a unidirectional (AUZ) and fully reversible (ARP) version. This range of oval jet fans excels in low noise levels. The installation height is 422mm.

These compact and robust jet fans have been developed especially for the use in car parks. The jet fans have been designed for an optimal capacity, long life span and very reliable operation.

More information

The internal fan housing consists of a round fan casing with flanges. Oval silencers have been mounted on both sides on the fan casing. The fan has been constructed with guide vanes for an optimal aerodynamic efficiency. On the unidirectional version a wire guard is mounted on the inlet side and a deflector on the discharge side. With deflectors the air stream flows in the desired direction. On the reversible version deflectors are mounted on both sides of the fan. As standard, the jet fans are equipped with mounting feet for direct mounting to the ceiling or wall.

The impeller consists of a hub in which special casted aluminium impeller blades have been mounted at a pre-determined pitch angle. The impeller is coupled directly onto the motor shaft. All fans are statically and dynamically balanced in acc. with VDI 2060, ISO 1940, 1-1986 Class Q 6.3.

The motor is two-speed 3x400V, 50Hz or 3x380V, 60Hz for direct start. Motor protection min. IP55 in accordance with IEC 34-5. Insulation class F or H depending on temperature protection. The jet fans are equipped with a terminal box on the outside of the fan casing.

As standard, the fan casings and mounting frames are hot-dip galvanized steel. The silencers are an Aluzink execution. A powder coating in any desired color is available as an option. In the standard execution the jet fans meet the requirements for operation in unheated, low corrosive environments according to DS/EN ISO 12944-2, corrosion category C3.

The standard operating temperature is from -20 until +40°C. Jet fans for hot smoke removal are certified according to the EN 12101 part 3 in the classes F200/F300/F400. 

  • All F300 fans have been tested at 300°C / 120 min
  • Class F400 is only available for 50Hz.

 

Catalog

Manual:

More languages and information at: https://www.novenco-building.com/products/car-park-fans/jet-fans-auz-arp/


Jet Fans AUT ART

Basic car park jet fans in a unidirectional (AUT) and fully reversible (ART) version. The installation height is 422 mm.

These compact and robust jet fans have been developed especially for the use in car parks. The jet fans have been designed for an optimal capacity, long life span and very reliable operation.

More information

The jet fan consists of a round fan casing with an inlet cone on both sides to minimize the inlet losses. The fan has been constructed with guide vanes for an optimal aerodynamic efficiency. On both sides internal wire guards are mounted. With a special internal deflector the air stream flows in the desired direction. On the reversible version internal deflectors are mounted on both sides of the fan. As standard, the jet fans are equipped with mounting feet for direct mounting to the ceiling or wall.

The impeller consists of a NovAx hub in which special casted aluminium impeller blades have been mounted at a pre-determined pitch angle. The impeller is coupled directly onto the motor shaft. All NovAx fans are statically and dynamically balanced in accordance with VDI 2060, ISO 1940 Class Q 6.3.

The motor is two-speed 3x400V, 50Hz or 3x380V, 60Hz for direct start. Motor protection min. IP55 in accordance with IEC 34-5. Insulation class F or H depending on temperature protection. The jet fans have external terminal boxes.

As standard, all jet fans are delivered in a galvanized execution. A powder coating in any desired color is available as an option. In the standard execution the jet fans meet the requirements for operation in unheated, low corrosive environments according to DS/EN ISO 12944-2, corrosion category C3.

The standard operating temperature is from -20 to +40 °C. Jet fans for hot smoke removal are certified according to the EN 12101 part 3 in the classes F200/F300/F400. 

  • All F300 fans have been tested at 300°C / 120 min
  • Class F400 is only available for 50 Hz.

 

Catalog

Manual:

More languages and information at: https://www.novenco-building.com/products/car-park-fans/jet-fans-aut-art/


Jet Fans AUO ARO

The ARO-AUO are reversible (ARO) and unidirectional (AUO) jet fans for conventional operation and operation during fires in car parks. The design is characterised by the oval silencers and employs the renowned NovAx axial flow fans. The fans are tested and approved to meet requirements for smoke exhaust.

Product facts

  • For car park installation
  • Three impeller diameters of Ø290, Ø380 or Ø500 mm
  • Standard temperature range -20 to +40 °C
  • Thrusts between 5 and 111 N
  • Sound pressures between 35 and 64 dB(A)
  • Two-speed motors are standard
  • Low sound level
  • F200, F300 and F400 approved for smoke extract
  • Outer casing of 3 mm sheet steel
  • Hub of galvanised steel
  • Impeller blades of aluminium
  • Deflectors on the outlets and for ARO also on the inlet
  • Wire guard on the inlet for AUO

 

Catalog

Manual:

More languages and information at: https://www.novenco-building.com/products/car-park-fans/jet-fans-auo-aro/


Jet Fans AZT

Compact and unidirectional car park jet fans (AZT) with adjustable outlet and low fan height.

Fans of the AZT type are especially robust, compact and perfect for car parks. The jet fans have optimal capacity, long life spans, reliable operation and are service-friendly.

More information

The fan casing is round with an integrated inlet cone and an adjustable outlet cone. This minimises the inlet loss and provides optimum control of the outlet airflow. The fan has guide vanes to improve the aerodynamic efficiency. A wire guard is mounted on the inlet cone. The installation is simple due to an innovative and new easy click-click design. Once the base plate is mounted to the ceiling, the fan is simply clicked in position and secured with fasteners. The total installation is 530 mm.

The impeller consists of a ZerAx hub with aluminium impeller blades in pre-determined pitch angles. The impeller sits directly on the motor shaft. All ZerAx fans are statically and dynamically balanced in accordance with VDI 2060, ISO 1940 Class Q 6.3.

The motors are two-speed 3×400 V or 3×380 V, both in 50 or 60 Hz versions. Motor protection is min. IP55 in accordance with IEC 34-5. The jet fans have external terminal boxes. Damping of vibrations is unnecessary due to the balanced and stable running of the ZerAx fans.

The fan casing is of pre-galvanised sheet steel, which can be optionally powder coated in any desired colour. In standard execution, the jet fans meet the requirements for operation in unheated, low corrosive environments according to DS/EN ISO 12944-2, corrosion category C3.

The standard operating temperature is from -20 to +55 °C. The fans for are certified for removal of hot smoke according to the EN 12101 part 3 in the classes F200120 and F30060.

  • F200120 fans tested at 300 °C / 120 min.
  • F30060 fans tested at 300 °C / 120 min.

 

Catalog

Manual:

More languages and information at: https://www.novenco-building.com/products/car-park-fans/jet-fans-azt/


Jet Fans CGF

Centrifugal design car park jet fans in a unidirectional execution. This range of centrifugal design jet fans excel in low built-in heights, high efficiency and low noise level. The installation height is only 268mm.

These compact and robust jet fans have been developed especially for the use in car parks. The jet fans have been designed for an optimal capacity, long life span and very reliable operation.

More information

The jet fan consists of a flat centrifugal fan Aluzink casing with an inlet cone on the bottom side to minimize the inlet losses. On the inlet side wire guards are mounted. With a special internal deflector the air stream flows in the desired direction. As standard, the jet fans are equipped with mounting feet for direct mounting to the ceiling.

The centrifugal impeller is coupled directly onto the motor shaft. All fans are statically and dynamically balanced in accordance with VDI 2060, ISO 1940 Class Q 6.3.

The motor is two-speed 3×400 Volt, 50 Hz for direct start. Motor protection min. IP55 in accordance with IEC 34-5. Insulation class F or H depending on temperature protection. The centrifugal jet fans have a terminal box which is integrated into the fan housing.

As standard, all jet fans are delivered in an Aluzink execution. In the standard execution the jet fans meet the requirements for operation in unheated, low corrosive environments according to DS/EN ISO 12944-2, corrosion category C3.

The jet fans have been designed to comply with all the international machinery safety standards according to EN ISO 14121-1:2007.

The standard operating temperature is from -20°C until +40°C. Jet fans for hot smoke removal are certified in accordance to the EN 12101-3 in the classes F200 and F300.

  • All F300 fans have been tested at 300°C / 120 min

 

Catalog

Manual:

More languages and information at: https://www.novenco-building.com/products/car-park-fans/jet-fans-cgf/